Tunnel Pushfiller Used in Coal Mine
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 20 Sets per Month set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.high quality and low cost
2.high capacity and easy operation
3.very wided used in mining industry
HTJ-800-37 Roadway Pushfiller Machine Main features:
The structure of this machine is simple, the operation is convenient, easy to maintain
The system pressure is low, the leakage of the hydraulic oil is just little, the filling efficiency is
High and the filling result is good.
Applications scopes:
This machine is used for backfilling the waste rocks in the goaf roadway in the underground mine so that the roadway can be filling mined, The buildings on the ground pressure of coal pillar roadway layout for filling gangue, in this way the subsidence of surface can be well controlled and the buildings are safe. Exchange rock wastes with coal, and the rock wastes will not be lifted onto the ground, there is no rock waste hill, the recovery of the resource is much higher, it is good for the environmental protection of the coal in the ground, so, which can get comprehensive economic benefits.
backfilling amount of the rock waste | 200I/H |
Applicable roadway height | 2.8m-4.5m |
Applicableroadway width | 2.5m-5.5m |
Applicable roadway inclination | ±16° |
feeding unloading rotary drum diameter | 320mm |
feeding conveyor speed | 2m/s |
feeding belt conveyor width | 800mm |
feeding unloading adjusting deviation angle | 9° |
feeding unloading adjusting partial distance | 400mm |
levelling angle for levelling mechanism | ±6° |
casting belt electricity roller power | 11KW |
casting belt electricity roller diameter | Φ500mm |
Casting belt conveyor width | 800mm |
Speed of the casting belt | 3.15m/s |
Adjusting scope of casting height | 2.8-4.5m |
Adjusting scope of casting width | 2.5-5.5m |
Speed of the crawler belt | 0-9m/min |
The biggest working pressure of hydraulic
system | 16 MPa |
Capacity of tank | 200L |
Electric controlling device | The flame-proofand essential security
form |
service voltage | 1140/660v |
voltage of controlling supply | 36V 24V |
rated current | 200A |
L W H (Minimum) | 13000mmx2150mmx2500mm |
Weight | ≈20T |
- Q:Where is the problem of boring machine knowledge?
- No table feed mechanism, spindle box, column mounted on the skateboard, the slide can be moved along the bed guide.
- Q:Boring machine boring how to adjust the knife
- Often rough boring knife like a 45 degree knife fine boring knife like truncated turning tools, rough boring to stay the amount of 0.1, and then use a fine boring knife with a plane scraping shape.
- Q:Boring machine - how to find the dry steel
- I do not know what kind of bed you use, what kind of work to live
- Q:Boring machine boring 15O hole, the length of 1600mm.
- Note: If the workpiece hole diameter of 140mm, boring bar diameter to 80mm for the wonderful, too thick is the impact of boring during the chip, there will be dirt phenomenon; overfill
- Q:About boring machine tool introduction
- Roughing to cut the main margin, as long as the rigidity enough, the margin can be relatively large; do finishing is generally fine boring for the margin, it is necessary to ensure that the boring hole to meet the requirements but also to ensure that the hole size between the correct
- Q:The detailed heat treatment process of boring bar made of 38CrMoAl steel boring machine
- Quality (the workpiece to obtain a comprehensive mechanical properties, quenching and tempering generally take 28-30HRC) - fine car to wear the amount of (each side of the single-sided are retained 0.2-0.25mm) - pliers milling milling line - milling tail and related holes
- Q:Zhongjie boring machine t68 wire rope how to replace
- Reverse jog and forward jog similar to the operation by the SB4, contactor KM2 and KM6 with each other to complete the action.
- Q:Horizontal boring machine flat turntable how to use?
- The cutting tool is installed in the cone hole at the front end of the spindle, or is mounted on the radial turret of the flat plate. During the working process, the spindle rotates one side and moves in the axial direction.
- Q:What is drilling and boring
- ⒊ large amount of cutting, chip removal difficult, easy to produce vibration.
- Q:Horizontal boring machine t68 can boring diameter 50mm hole it
- Etc., mainly used in single-piece small batch production and repair shop, processing hole roundness error of not more than 5 microns, surface roughness Ra0.63 ~ 1.25 microns.
1. Manufacturer Overview |
|
---|---|
Location | Shanghai, China (Mainland) |
Year Established | 2000 |
Annual Output Value | Above US$100 Million |
Main Markets | Southeast Asia Africa Mid East Eastern Asia South Asia |
Company Certifications | ISO certificate |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | shanghai |
Export Percentage | 51% - 60% |
No.of Employees in Trade Department | |
Language Spoken: | English, Chinese |
b)Factory Information | |
Factory Size: | 3,000-5,000 square meters |
No. of Production Lines | 10 |
Contract Manufacturing | OEM Service Offered Design Service Offered Buyer Label Offered |
Product Price Range | AVERAGE |
Send your message to us
Tunnel Pushfiller Used in Coal Mine
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 20 Sets per Month set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches