The good Factory Direct Custom Made Double Acting Hydraulic Ram

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q:What is the basic working principle of the cushion device in the hydraulic cylinder?: For the high-pressure system, also need auxiliary measures to cushion cylinder movement impact, close at each end of the cylinder stroke position, set the stroke the switch is controlled by the stroke switch of the hydraulic cylinder flow;

Q:How much money machine hele ah, pneumatic hele surface machine, hydraulic machine hele surface what is the difference between ah: the user can use the back to add hydraulic oil, pneumatic delivery manufacturers generally do not take the pump, because the pump volume, will increase the cost of logistics,

Q:What is the pivot shaft in the cylinder?: The hinge shaft is a kind of hydraulic installation method. After installation, the hydraulic cylinder can swing. This cylinder is a hydraulic cylinder with a hinged shaft.

Q:How do I calculate the flow rate of the hydraulic cylinder?: Hydraulic cylinder flow = hydraulic cylinder piston cross section * speedFor example: the cylinder speed of D10cm requires 10cm per secondThe hydraulic cylinder piston cross-section =pi * D * D, 4=3.14 * 10 * 10 4=78.5 / cm2Flow per second =78.5 * 10=785 ml =0.785 litersThe flow rate is =0.785 * 60=47.1 liters per minute

Q:What is it used for? What kind of factory is likely to be used in general?: As hydraulic technology has many advantages, from civil to national defense, from general transmission to precision control, it has been widely used. In the mechanical industry, currently has 85% machine tool drive system adopts hydraulic transmission and control, such as grinding, milling, planing, pulling, and combined lathe; in engineering machinery, is widely used in hydraulic transmission, such as excavator, wheel loader, auto starter, bulldozer, scraper, grader, roller machine; in agricultural machinery, which has been used to combine harvester, tractor, tool suspension system; in the automotive industry, hydraulic brake, hydraulic dump, fire etc. are widely used; in the metallurgical industry, such as electric control system, rolling mill control system, charging, ing converter control, control of blast furnace;

Q:How to remove the hydraulic cylinder oil seal?: Is the O ring squeezed out? The front cover should be threaded, carefully to see if there are holes installed, there should be 2 or 4, is not to be painted over, if not, must use the flat shovel.

Q:What is the four link mechanism of hydraulic support?: The four link mechanism is an important part of the hydraulic support, including: connecting rod, rear connecting rod, shield beam and base. The design of the four link determines the trajectory of the top beam, the force of the connecting rod and the shield beam also determines the size and size of the overall size of the support.

Q:Urgent, how, on the mechanical hydraulic buffer for a large amount? What mechanical pneumatic elements are used?: There are large amounts of buffers on machines with actuators, such as cylinders, guides, etc.Large amount of pneumatic components - assembly line, a high degree of automation special plane, PCB detection, paste, exposure, screw machine, mechanical hand, vulcanizing machine, press, and so on

Q:UG4.0 parts library, what cylinders, motors, cylinders are standard parts for the equipment?: There are a lot of gears, bearings, such as motor, Oriental motor, MISUMI Schneider, Misumi etc.. There are more than 400 manufacturers of product models, massive.

Q:We have to design a manual plunger water hydraulic pump, but the wall thickness of the cylinder will not be designed and checked. I follow the sigma delta is not less than PD/2[design is out of 10mm thick, but the teacher said 5mm can withstand the pressure of 150MPa, the material with corrosion resistant stainless steel can. Some of my parameters are the maximum cylinder pressure 140MPa, cylinder size d=18mm (can also be smaller), length 60 ~ 80mm, how can I design wall thickness? thank you very much indeed: Thick wall steel tube branch pipes and thin-wall pipes, the different calculation of bearing pressure in the formula, K=D/d = 1.2, the tube called a thin-walled tube; K=D/d>1.2 tube called thick wall pipe.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range