QM16160 ACCU-LOCK MACHINE VICE
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
We are a specialized company for machine vises , whoseproducts are exported to Europe and America as well as developed countries .Wehave Q12,Q13,Q41,QM,QMN series .All the products have high precision ,and reasonabledesigns and reach the JB/T2329-11 standards .
Weare insisting that the quality is first and reputation is the best. We refocusing on our quality and innovation , We are looking forward to havingopportunities to set up more business relations with customers from all overthe word and establish the long-term cooperation with best products and perfectafter-service.
QM Series MachineVice
Performance and character:
1. It is one of main attachmentsfor milling、drillingmachine ,it is particularly suitable for the finishing of precision parts.
2. The accuracy of vice (parallelismand squareness) is 0.025mm/100mm.
3. The special segment in themovable jaw forces the vertical pressure downward when the horizontal pressureworks, so that this jaw does not lift the work piece.
4. Four positions allow extracapacity to change opening of jaw.
- Q:What is the difference between the heavy duty and the light, how to choose the size of the tongs, usually 8 inches or 10 inches
- Also, don't know what to buy? There were a dozen, dozens, and a hundred, and more than two hundred, five hundred and six hundred, and I didn't know how much to buy. I'm a diy knife, black hey!
- Q:What is the commonly used workpiece in milling machine
- Correct and reasonable use of vice, can not only ensure the positioning precision of the clamping workpiece, but also can keep the accuracy of flat vice itself, prolong its service life. When using the pincers, the following points should be noted: 1) clean and clean shavings and oil, and keep the tongs of the vise. 2) maintain a fixed clamp and adjust it to the correct position on the workbench. In order to make the clamping reliable, make the work of the workpiece with the clamping surface area larger, the workpiece which is short in the width of the tongs is as possible as possible in the middle part:. 4) it is not too much for the clamps to be installed, and the pincers should be added at the mouth of the tongs, as shown in figure 6-8, when necessary. In the case of a long working unit, two or more parallel jaw vice is available to keep the clamp tight and prevent vibration when cutting. 6) to the root
- Q:Who knows the calculation and selection of the tongs?
- When there must be a pretension and the need for regular adjustment in the use of wear, it should be used for pre-tightening or the pre-compact structure of the double nut thread. With good dustproof condition, and only need to adjust the clearance and pre-tightening force when assembling, the structure can be adjusted by using the simple double nut gasket
- Q:What are the characteristics and advantages of precision vice?
- Precision pliers structure similar to ordinary clamp structure, is a clamp body activity, fixed jaw, jaw, drive screw, nut, is only relevant parts of higher precision, cooperate more closely. There is no necessary relationship between structure principle and precision
- Q:Common production desk vice, 45 # steel make the clamp plate, how to make pattern
- 45 # steel jaw plate, heat treatment at 860 ℃ quenching, quenching oil cooling water, 500 ℃ tempering hardness in HB300-350, can satisfy the requirement of general hardness and toughness.
- Q:Push it to the required piece of work, then lock the screw with the inner hexagon wrench to achieve a tight end. What I want to know is the design structure of it, if you have this kind of vice in your hand, you can show me a few pictures, especially the lock structure underneath it. There is a drawing change. If you know what it's called, give it a name,
- This structure used to be used mainly for the precision flat tongs used in grinding machines.
- Q:Ask questions! How large a bench vice is a carpenter?
- Woodworking is not suitable for use of bench vice, different USES.I hope my answer will help you.
- Q:Numerical control milling machine vice school table
- With a dial indicato.I hope my answer will help you.r
- Q:Is the screw of a vice clamp a silk stick? How do you choose a screw with the same principle? The device requires a general assembly
- The screw on the top of the vice clamp is actually a silk pole. The first thing you don't know is how big a clamping device you want to do. It is recommended that you choose a silk rod that is no less than thirty in diameter (the specific pitch is chosen according to the actual situation). Note: the minimum material of the material is 45 steel. Silk mother chooses tin bronze silk mother.
- Q:The approximate variety of a vice
- The specification of table vice is indicated by the width of tongs, 100mm, 125mm, 150mm etc. The bench vice is a common fixture for holding the workpiece. There are two kinds of fixed and rotating type. According to the appearance function cent: have the anvil and no anvil two kinds.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
QM16160 ACCU-LOCK MACHINE VICE
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches