Heaters-Startup Heater
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Our company is the Leading Enterprise in petrochemical & coal chemical industrial heaters in China, the only heater manufacturer in Top Fifty (50) enterprises certified by CPEIA in related industries and the rare enterprise which is capable of EPC among similar enterprises in China. As the Leading Enterprise of Fired Heaters, Corporation has rich experience in design and fabrication of Incinerators. Corporation has designed and fabricated various kinds of Incinerators such as Sulphur Recovery Units (1.5*104 t/a, 2*104 t/a, 3*104 t/a and 5*104 t/a), Asphalt Unit Off-gas Incinerators (1*105 t/a and 5*105 t/a), Styrene-Butadiene Solution (SBS) Rubber Combination Unit (7*104 t/a), Dimethyl Ether Unit (4*105 t/a), Acid Gas Incinerators for Stripping Unit of Acidic Waste Water, Heavy Oil Catalytic Cracking Unit (6*105 t/a), etc.
As the Leading Enterprise of Fired Heaters, Corporation has rich experience in design and fabrication of Preheaters. Corporation has designed and fabricated various kinds of Preheaters such as Preheater for Methanol Unit (1*105 t/a, 1.5*105 t/a and 2*105 t/a), Oxygen Preheater for Acetylene Unit of Comprehensive Utilization Unit of Potassic Fertilizer Production (1*106 t), Preheater for Comprehensive Utilization Unit Transforming of Medium-low temperature Coal Tar (12*104 t/a), Hydrogen (Hydrogenation) Preheater for Light Oil Hydrogenation Unit (4*105 t/a), etc.
Corporation has designed and fabricated various kinds of Startup Fired Heaters such as Startup Fired Heater for Synthetic Ammonia Unit (1.8*105 t/a, 2*105 t/a and 5*105 t/a), Startup Fired Heater for 6000Nm3/h Hydrogen Installation, Startup Nitrogen Fired Heater for Production of Coke-oven Gas-to-methanol, Startup Air Fired Heater for Acrylonitrile Extension (2.12*105 t/a), etc.
GROUP mainly produces the following products:
l Refinery/chemical furnaces, incinerators, coal (liquid) chemical reformers
l Waste heat boilers, thermal medium boilers
l Class A1 /A2 pressure vessels
l Reactors, Heat Exchangers & Towers
l Oil tanks/accessories/mixers, alloy steel precision castings
l Four classes of piping supports and hangers used in fired-electric/thermo-electric/nuclear electric power industries and dampers
l Flue gas/air/coal powder duct and its attachments
Boiler ancillaries, water treatment devices and so on
- Q:What is the difference in structure between industrial furnace and boiler?
- Industrial furnace: main heating, steel and other metal materials, or ore and other materials. An industrial furnace of higher temperature, such as forging or heat treatment. Therefore, the energy consumption is large, and the insulation layer is designed to be thicker, and the structure is designed for the final purpose of the production purpose, the product process and the production efficiency.
- Q:What are the advantages of a vacuum furnace?
- The utility model can completely eliminate the oxidation and decarburization of the workpiece surface in the heating process, and can obtain clean surfaces without deterioration layers. For cutting tools that grind only one side of grinding (such as twist grinding, the surface of the groove surface is exposed to the blade directly), the cutting performance is greatly improved.
- Q:What's the role of anchor bricks in industrial furnaces?
- The wall of an industrial furnace or flue is mainly composed of an inner lining layer, a heat insulating layer and an outer wall layer. The lining is a refractory brick, and the outer wall is an ordinary sintered brick.
- Q:Selection of heat preservation material for industrial furnace
- Micro nano heat insulation board.The thermal conductivity of micro nano heat insulation board is very low, only a fraction of the traditional thermal insulation material, and the insulation effect is very efficient.
- Q:Why does the burner of industrial furnace burn occasionally?
- The general process for burner ignition, blowing furnace, electric spark ignition, solenoid valve, open the gas in case of delayed spark ignition, detection device detects the flame, the controller accepts signal so that the solenoid valve open, gas continuous normal combustion. However, if the ignition fails or the burner fires, the detector cannot detect the flame, which causes the solenoid valve to close and the burner flameout.
- Q:What is an industrial furnace pit?
- Later, a chamber kiln with a semi closed or fully enclosed kiln made of refractory bricks can be used as fuel for coal, gas or oil, and electricity can be used as heat source. The workpiece will be heated in the kiln hearth.
- Q:Brief introduction to repair of industrial furnace
- Compared with other equipment, industrial furnace repair has many characteristics: more repair times, more maintenance costs, more non-standard equipment and unsafe factors.
- Q:What are the companies in the world that are currently engaged in metallurgical furnaces?
- There are many kinds of furnaces in metallurgical industry,colored and black,smelting and heat treatment are also included.
- Q:What is industrial furnace masonry?
- Masonry industrial furnaces refers to complete materials such as brick kilns in construction process.
- Q:What is the difference between industrial furnaces and boilers?
- Hot water or steam generated in the boiler can directly provide necessary energy for industrial production and people's life, but also by the steam power device is converted to mechanical energy, or through the generator converts mechanical energy into electrical energy. Hot water boilers are called hot water boilers. They are mainly used in daily life, and are also used in industrial production. Steam generating boilers are called steam boilers, often referred to as boilers. They are used in thermal power stations, ships, locomotives and industrial and mining enterprises.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Heaters-Startup Heater
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords