Bearings single row tapered roller, model 32028
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
- Single row Tapered roller bearings
Single row roller bearings can only bear the shaft or shell of a direction of the axial
displacement and a direction of the axial load. So we need the two bearing face to face or
back to back to use.
★Product features
The inner and outer ring raceways are segments of cones and the rollers are also made with a taper so that the conical surfaces of the
raceways and the roller axes if projected, would all meet at a common point on the main axis of the bearing. The rollers are guided by a
flange on the inner ring. This stops the rollers from sliding out at high speed due to their momentum. The larger the half angles of these
cones the larger the axial force that the bearing can sustain.
★Product application
In many applications tapered roller bearings are used in back-to-back pairs so that axial
forces can be supported equally in either direction.
Pairs of tapered roller bearings are used in:
- car and vehicle wheel
- mining equipment
- moderate speed
- engine motors
- axle systems
- construction
- agriculture
- reducers
- gear box
★Horton tapered roller bearings Basic size
- Single row tapered roller bearings:
Inner ring size: 20mm ~ 1270mm Outer ring size: 40mm ~ 1460mm Width size: 15mm ~ 240mm
- Double row tapered roller bearings:
Inner ring size: 38mm ~ 1560mm Outer ring size: 70mm ~ 1800mm Width size: 50mm ~ 460mm
- Four row tapered roller bearings:
Inner ring size: 130mm ~ 1600mm Outer ring size: 200mm ~ 2000mm Width size: 510mm ~ 1150mm
★Tolerance:
Horton tapered roller bearing with common
tolerance, and also provides P6X, P6, P5, P4,
★Radial clearance
Horton single row tapered roller bearings only
in after installation have clearance, and in
★Cage
Tapered roller bearing general ues the steel plate stamping, basket shape cage, but when the size is bigger, we
also adopts entity cage.
1. Outside diameter D ≤ 650mm, use the steel plate stamping cage, cage postposition without code mark.
2. Outside diameter D > 650 mm, use the steel entity prop cage, cage postposition without code mark.
★Dynamic equivalent load
P = Fr [KN], Fa / Fr ≤ e;
P = 0.4Fr + YFa [KN], Fa / Fr > e.
The single row tapered roller bearings used in pairs (basic physical size can be different), when calculation the
equivalent dynamic load of the bearing, must be included in the radial load cause additional axial force. The single
row tapered roller bearing additional axial force S, can approximate formula: S = Fr / 2y
★Static equivalent load
Single row tapered roller bearings
P0 = 0.5Fr + Y0Fa [KN] P0 < Fr, then P0 = Fr
Double row tapered roller bearings
P = 0Fr + Y1Fa [KN],Fa/Fre ≤e P = 0.67Fr + Y2Fa [KN], Fa/Fre > e
- Q:Is the tapered roller bearing so correct?
- Tapered roller bearings are designed for the inner ring, outer ring raceway and roller cone vertex on the central axis of the bearing, radial load acting on the bearing, axial force is generated. Therefore, it is necessary to use the 2 bearings for use, or as double pairs of bearings, double row bearings. Combination and double row tapered roller bearings, when radial loads act on tapered roller bearings
- Q:that is to say, the taper head is the face and the back is the back
- When you remove the outer ring of the tapered roller bearing, you will see that the components of the inner ring cage are large and smallLook at the axial force you are using. The direction of the axial force in that direction is consistent with the direction of the small one,
- Q:Online cylinder cones are GB/T4663, what do you mean?
- Which size do you want, eldest brother? How do I make so much?GB/T: recommended national standards; GB: mandatory national standards4663: taper roller national standard codeThere is a missing release year later!It should be: GB/T 4663-1994
- Q:Tapered roller bearing: Bearing expert why burned or locked
- Shaft tolerance is relatively small and fine head, the inner shell inside and nose has obvious signs of friction. If there are traces of friction on one side or on both sides of the inner shell, there is an abnormal contact with the inner shell of the bearing and the friction of the inner shell of the bearing.2, the inner shell shell burning marks are not serious, roller black even deformation, generally is the inner shell or casing tolerance, Ambassador bearing gap smaller, and even negative tolerance caused by burning. Or in the maintenance of the bearing selection is not correct, you can use large clearance bearings.3, the shell burned seriously, the inner shell, roller are no obvious changes, you can observe whether the shell has traces of friction. There are traces of friction on the outside, and it can be considered that the tolerance between the bearing shell and the shaft is insufficient, which results in abnormal friction caused by the slipping of the housing. If there are traces of friction on one side or on both sides of the shell, there is an abnormal contact between the component relative to the bearing housing and the bearing housing, and the heat generated by friction will be burned out.
- Q:The installation of tapered roller bearings
- 1, for example, a shaft needs to be fitted with two such bearings at both ends. Can it be installed in the same direction?The force of the shaft is concerned. If the shaft is indeed subjected to one-way axial force, of course, it can be installed in the same direction. If it is subjected to biaxial axial force, it will not work
- Q:Tapered roller bearing suffix code YA2 stands for what does that mean?
- Mr. Liu five love reading, "gladly forget to eat" every knowing; ong drinking is not wine, but for mountains and rivers ". So Mr. Qian Zhongshu proposed" all happiness enjoy all belong to the spirit of "the world as truth, but think, feel spiritual satisfaction is also flawed, sometimes even the feeble.
- Q:What are the general uses of tapered roller bearings?
- At the time of greater radial load and axial load
- Q:Tapered roller bearings. Are the rollers tapered?
- As the name suggests, the roller of tapered roller bearings is conical, rather than a frustum of a cone. The roller of cylindrical roller bearings is cylindrical.
- Q:Why is the cage of tapered roller bearings loose?
- It is loose, the outer frame of the bearing cone is removable, as long as it is easy to install and add lubricant. You can come up with the relevant standards, must belong to the bearing standard parts, as long as you meet the standard requirements of the bearing can be spread!
- Q:What items should be inspected for tapered bearings?
- 4, tapered roller bearing ring after the whole machine after pickling, there should be no scald, the name of cooperation should not be a pickling visible traces of burns, and no response angle detection.Tapered roller bearing appearance should be smooth, lubrication, no plants, no scratches, no rust and no obviously difference, promised to pressure injury, damage, deformation and defects such as trachoma vipassana.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Bearings single row tapered roller, model 32028
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords