False Ceiling Grid System

Hot Products

Ceiling T Grid System for Suspended Ceiling

Suspension Ceiling Tee Grid -Plane Tee Grid

Suspension System Frame for Ceiling Tiles-Ceiling Tee Bar

Suspended ceiling grids drop ceiling grid prices

Suspension Ceiling Tee Grid for Acoustic Ceiling

Galvanized Suspension Ceiling Tee Grid for Ceiling

Black suspended ceiling grid ceiling system

Suspension Ceiling Tee Grid for Ceiling System

Gypsum Board T-Grid T Bar for Ceiling Suspension Groove Wall Angle Ceiling T-Grid

Suspension Ceiling Tee Grid-Metal Ceiling Grid

FAQ

What is the keel of the ceiling?

If it is home improvement ceiling with ordinary light steel keel on the line, tooling, then it is recommended to use paint keel with mineral wool board.

I want a drop-down ceiling for my basement, you know with panels and a grid. What is the average cost for a pretty large room? Don't worry about a contractor. My dad is a contractor so no cost for installation. I don't think you even need a contractor for this though. I just need to know if it's affordable. I have a large basement and we need to be able to access the vents and pipes easily through the panels. There's no other option (unless there's an alternative). Thanks :D

affordable is what you can afford..however..measure the area and go to home depot or Lowe's and see how much you are looking at in materials..and if dad will do the install for free that's a plus..now there is the dry wall the ceiling option but as you stated earlier you need to have access to vents and pipes..so the smart choice obviously is to do a drop ceiling..the latter will hurt more with dry wall trying to re patch and repair anything later above the ceiling..and with the drop ceiling you can figure out if you can afford to do 10x10 sections or the hole thing at once..very much affordable and very wise choice..

Prepare the ceiling, want to know how to use light steel keel is long, such as a light steel keel is 3 meters long, and my room is 4.8 meters long, that keel is how to pick up to ensure the length of the Can I guarantee strength?

Do not have a special connector ah. Wood workers now have a tool in hand, the two keel lap, in the coincidence of the parts directly with a few pressure tools, you can. Similar to the rivet, but this tool does not pull rivets, it is directly to the two layers of keel out of a small hole, huh, huh. Woodworking all know.

Light steel keel d60 and u60 What is the difference?

Light steel keel d60 refers to a kind of hanging keel. Light steel keel u60 cross section in the form of U-shaped keel.

The question says it all, I need to know this because I need to hang something up that weighs about 100-120 pounds. I need to know which section of the grid of ceiling girders holds the most weight. The long sections between the intersections?The short sections between the intersections?Or the intersections themselves?If you dont remember what that looks like, think of your elementary school or work office. Yeah. those kinds of ceiling tiles, just the plain old styrofoam style stuff.I need an answer from a legitimate source, not a guestimation.

It depends on the installation. I would expect 100-120 pounds to be too much for almost all installations. 20-30 pounds is easily possible on almost all if supported over several feet of the rail and not just hung from one or two of the grid clamps sold for the purpose of putting up signs or displays. For example, the circular air conditioning outlets used in some stores that are connected by flexible ducts to the main ducts and the fluorescent light fixtures that lay in the openings weigh about 10 pounds. The variation is due to the location of the hanging wires for the grid and what the weight is doing. I would expect a hanging point directly under a vertical 16 ga. wire running up to the building structure/roof would probably be able to take 40-50 pounds if the wire were well twisted at both ends - but the wires are often just pushed through the hole and bent with a single hook. I am certain that 100 pounds applied in the middle of a rail between two support points is going to bend the rail in any common installation. To hold that much weight safely, I think you are going to have to run a wire through a slot or hole in the tile, up through the upper structure and tie into the building directly, especially if there is any chance of movement by wind, AC air flow, or people bumping the suspended item.

Light steel keel manufacturers is not only the production of light steel keel?

In addition to our light steel keel will produce paint keel, triangular keel, stone and so on. But small factories are generally only the production of light steel keel.

Will the light steel keel and C steel What is the difference?

Use different, light steel keel is mainly used for decoration, bearing low, more than 60 keel to load people, and C steel is mainly used for steel structure bracket, beams, ribs and so on;

How hard is it to remove a hung ceiling?

It wasn't that hard. We removed the tiles, which were attached, not the drop in tile type, then we had to remove the grid, however we didn't have to be as careful as you may have to be, we suspected we'd have to gut the ceiling anyway. But PEB is right, you may not like what's underneath. We had the drop ceiling attached to an old plaster and lath ceiling, which we removed and down came a ton of grimey blown in insulation. But we like our 9 foot ceilings, now done in sheetrock, so much better. Good Luck!