Slitting and Cut to Length Line-galvanized steel
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Processing flow is as following:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
- Q:What is the difference between a slitter and a slitter?
- In our life, the application of the sub machine still has a lot of, like in packaging, textile, clothing and many other industries, he can be very good for cutting of silk, cloth and plastic braid, he is used to automatic temperature control heating operation.
- Q:What is a striping machine?
- Remember that you can't fully bite before making the knife and leave some space. When the balance of the knife is fully adjusted, the knife can be completely cut off, and the knife depth is close to the surface thickness of the roll.
- Q:How do metal slitting machines cut out knives?
- If there is no, then the operator can only be based on some operational experience, etc.. However, it should be noted that for the blade clearance, it is necessary to control the good, so as not to affect the slitting effect.
- Q:Slitting machine, pc0.8 mm coil, why have rough edges?
- Check whether the matching sensor device is connected properly at frist.
- Q:What is the difference between CNC slitting machine and slitting machine?
- CNC cutting machine, cutting machine and roll a large, similar to what size will directly cut. CNC slitting machine, then the main cut, there is a shaft discharge, and another shaft winding, the middle through the knife.
- Q:How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- A variety of equipment will be the entire corrugated cardboard production process organically combine, so that its continuous production. The traditional methods of combined production of more units and single machines not only have high production efficiency, low labor intensity, but also operate centralized control, which is simple, safe and low noise. The most important thing is that the corrugated paperboard produced is of high quality.
- Q:How to adjust the pearl cotton separator?
- Adjust the paper holder of the pearl cotton separator to the right distance.
- Q:Is the tape on the tape slitting machine a good one at the back or a good one in front?
- If you are concerned about the volume from the front. Mainly depends on your mother roll size, whether to change regularly, the quality of mother roll, how about, do not pay attention to its condition. Very few people ask this, I may not consider the full, you have the right to reference!
- Q:Slitting machine, slitting machine looper (pit cause analysis) in the strip of varying lengths
- The tension of the tension mechanism is uneven, and the tension of the tension mechanism is big. Small matters determine the tightness of the take-up volume, and the outer diameter of the take-up strip with a large tension is smaller, otherwise it is large. The take-up speed of the coil with big outer diameter is larger.
- Q:What is the relationship between the arrangement of metal bars and the material thickness of the strips?
- The arrangement of the metal bar machine is directly proportional to the material thickness of the strip.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Slitting and Cut to Length Line-galvanized steel
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords
