Slitting and Cut to Length Line-Aluzinc steel coil

Slitting and Cut to Length Line-Aluzinc steel coil System 1

Slitting and Cut to Length Line-Aluzinc steel coil

Ref Price:

Loading Port:: Tianjin

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: 2000 unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

EPS Sandwich Panel Production Line

High Quality Discontinuous PU Sandwich Panel Product Line

Continuous Casting Machine for Steel

Razor Barbed Wire Machine Factory with ISO CE CO

Y81hydraulic automatic aluminum cheap baler machine01

LOW CARBON STEEL WIRE DRAWING MACHINE FACTORY

Paper wrapping machine for copper conductors

Chain Link Fence Machine with Full automatic and semi automatic

General Information：

High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.

Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.

It is takingthe place of brick to be a main material for building now.

Slitting and Cut to Length Line-Aluzinc steel coil

Processing flow is as following:

Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging

Technical Data：

1. Coil Thickness：0.3-4mm

2. Coil Width：300-1800mm

3. Coil Max. Weight：30 T

4. Coil I D：φ508-φ800mm

5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa

Q:What is the difference between a slitter and a slitter?: It is a kind of mechanical equipment used to cut wide width paper or thin film into many narrow materials. It is commonly used in paper making machinery and printing and packing machinery.Before the cutting machine of magnetic powder clutch speed is not high, because of high speed friction, in operation due to the magnetic powder to produce high temperature, shorten its service life, serious when the death card, make the machine run suffocate suffocate, bring very serious consequences for the production. Seriously affected production efficiency.

Q:What is a striping machine?: Remember that you can't fully bite before making the knife and leave some space. When the balance of the knife is fully adjusted, the knife can be completely cut off, and the knife depth is close to the surface thickness of the roll.

Q:There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?: The photoelectric proximity switch on the top photoelectric proximity switch or buffer pit at the top of the opener is damaged, and the silicon steel sheet can not be detected near the signal and should be replaced.

Q:Slitting machine; batten; place: The fixed position of the metal slitting machine when feeding trolley material should pay attention to the coordination and discharge power, prevent raw off injured foot. At the same time to ensure the position of the metal material in the uncoiler must be accurate.

Q:How do metal slitting machines cut out knives?: The cutting skills of the slitting machine in the bar machine, and its Pai skills, mainly depends on the specific situation. If it is a good quality slitting machine, then it will be equipped with cutter software to carry out the correct arrangement.

Q:Slitting machine, pc0.8 mm coil, why have rough edges?: Check whether the matching sensor device is connected properly at frist.

Q:The belt machine used for gluing buckles lacks power: The main reason is that the ignition advance angle is incorrect, the fuel pressure is too low, the intake system leaks, the throttle position sensor or air flow meter fails, the injector is not working well, and the EGR system is not working well.

Q:How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?: One is single-sided corrugated machine, first made of single-sided corrugated cardboard, and then through a single glue car processing, made into different structures and corrugated cardboard.

Q:Slitting machine, slitting machine looper (pit cause analysis) in the strip of varying lengths: The thickness of the raw material is uneven. Thick plate with a greater need of rolling force, rolling diameter leads to more and more big, the angular velocity of the same situation, the rolling line speed is faster, stay in the pit less material.

Q:What is the relationship between the arrangement of metal bars and the material thickness of the strips?: The arrangement of the metal bar machine is directly proportional to the material thickness of the strip.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range