Gate Valve Stem of Best Price and High Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Structure of Gate Valve Description：
A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.
2. Main Features of the Gate Valve：
• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber
• Free of water pollution
• High manufacturing accuracy
• High strength
• Environmental protection and energy saving
• Good visual effect
3. Images
4. Gate valve Specification
5.FAQ
1. What's are the characteristics of gate valve?
The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel.
2. What is the work principle of gate valve ？
The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry.
3. What is the structure?
Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.
- Q:What are the working principles of the electric gate valve?
- We see you what type of electric valve, is integral or ordinary type, if the overall type Denso took power on the line, is generally 380V and 220V power supply, and then according to their own needs and then open the signal line, in place and closing in place and remote control line, valve position feedback signal the commonly used 4~20ma over torque protection fault signal.
- Q:What is gate valve (with force transfer joint)?
- The force transfer joint is mainly used for the loose connection of pumps, valves and other accessories.
- Q:What's the difference between a soft seal gate valve and a hard sealed gate valve?
- Soft sealing gate valve is rubber seal, F sealed, hard sealing gate valve is the medium of particles.
- Q:Does the tap belong to a stop valve or a gate valve?
- Most taps are stop valves:1, gate valve (gate valve) is a headstock ram, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed doors, discomfort pumpsparameters vary, usually 5 degrees is not high, medium temperature is 2 degrees 52'. To improve its manufacturability, make up for the deviation of the angle of the sealing surface during processing. This gate is called an elastic ram.2, valve (stop, Globe, Valve) of the opening and closing parts are plug shaped valve, sealing surface is flat or sea cone, the valve along the center line of the valve seat in a straight line movement. Stem form of exercise (generic name: dark bar), but also lift rotating rod can be used to control air, water, steam, all kinds of corrosive media, mud, oil, metals and radioactive liquid media and other types of fluid flow. Therefore, this type of shut-off valve is very suitable for cutting or regulating and throttling. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation.The stop valve is an ascending stem type, and the handwheel rotates and rises along with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!
- Q:What is the difference between an elastic gate valve and a rigid gate?
- Brief introduction: the valve gate valve is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface to form a wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52'.Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate.
- Q:what are their applicable conditions? Advantages and disadvantages?
- Butterfly valve is a disc type of open and close parts reciprocating reciprocating about 90 degrees to open, close and adjust the fluid channel of a valve.Advantages: the butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, and torque is small, simple and rapid operation, and also has good flow characteristics of regulation and sealed off, is nearly 10 years the fastest growing valve, high temperature and high pressure, and to large diameter, high sealing function of the direction, long life, good adjusting features and a valve development.Disadvantages: the butterfly valve relative to the gate, ball valve pressure loss is relatively large, it is suitable for pressure loss requirements lax piping system.Under normal circumstances, it is not suitable for high temperature and high pressure pipeline system.Valve is closed parts (valve) moving along the centerline of the valve seat, the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional to, is also very suitable for the regulation of traffic.Advantages: in the process of opening and closing, the friction between the disc and the valve body is smaller than that of the gate valve, so it is wearableThe opening height is generally only 1/4 of the diameter of the seat channel, so it is much smaller than the gate valveGenerally, there is only one sealing surface on the body and disc, so the manufacturing process is good and easy to maintain;Disadvantages: the flow resistance coefficient is relatively large, resulting in pressure lossUnsuitable for large caliber productionThe opening and closing moment is larger and the structure length is longer.
- Q:The valve safety valve check valve + + + = exposed part of a water pump adapter? Five
- Generally do not require safety valve, just install exhaust valve in individual places.
- Q:Which is the most expensive, check valve and gate valve?
- In the case of DN50 Z15T-16 DN50: screw valve 46.200 thread copper bar gate valve Z15T-16 DN50 52 Z45F-16 DN50 97 flange valve flange valve rod Z44T-10 DN50 169 Z45T-116 DN50 flange valve dark bar 173 thread swing check valves DN50 52.090 thread straight type check valve DN50 57.280 flange screw check H44T DN50 129 flange valve lift check valve H41T-16 DN50 124
- Q:Gate valve z45h-10dn250 length of the body?
- Z45h-10dn250 body length L=330mm, this valve is hidden bar, elastic seat, sealing gate valve, gate lining, lining fluorine, belong to soft seal
- Q:What is plug welding gate valve?
- Plug connection pipeline welding mode safety gate valve
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Gate Valve Stem of Best Price and High Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
