Auto-climbing Bracket formwork and scaffolding system
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 m²
- Supply Capability:
- 1000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Auto-climbing Bracket ACB100 & ACB50
The power of the auto-climbing formwork is the hydraulic system, which includes the oil cylinder
and two commutators. The commutators can control the climbing of climbing rail and the bracket.
The steel rail and the bracket can inter-climbing, so the whole system will climb up steadily.
Cranes are not needed during the construction. It’s easy to operate, highly efficient and safe. It’s
the best choice for the construction of high buildings and bridges.
There are mainly two types of standard auto-climbing brackets, ACB-50 and ACB-100, the figure
means the push power of cylinder with unit of KN.
Characteristics:
◆ Perfect load bearing anchor system
Anchor system is the most important supporting part. The system is made of five parts shown
below. Thereinto, tensile bolt, V-climbing cone and washer can be taken out for reusing after the
concrete pouring finished.There are two kinds of anchor systems,A & B. A is matched with single
anchor shoe and B is matched with double anchor shoe.
◆ Crane-independent
Crane-independent forming, striking and climbing speeds up the work procedures on the
construction site and also makes them independent of each other. This means the planned
sequences can be maintained along with guaranteeing high productivity levels. The crane can
therefore be used for other tasks.
Hydraulic system is mainly made of two commutators,
oil cylinder and power distribution system.The
commutators can control the climbing of climbing rail
and bracket.
◆ High bearing capacity and safe
The stable working platforms are able to carry large loads, e.g. the storage of reinforcing steel
for the next climbing section. Generously-sized working platforms, the well thought-out design for
handling very high wind loads and the patented control function of the climbing mechanism are
some of the special details contained within the comprehensive safety concept.
◆ Platforms adjusted to suit the angle of inclination
The horizontal working areas thus created provide safe and comfortable conditions for
reinforcement work, shuttering and striking, concreting and finishing.
◆ The ACB formwork system can climb not only vertically but also slantways, the largest angle is
18 degrees.
◆ The system can climb up wholly or separately. The climbing process is steady, synchronous
and safe.
◆ The bracket will not fall to the ground until the construction is finished, the field will be saved
and the impacting breakage will be reduced (especially the panel).
◆ The system will furnish omnidirectional platform, the construction organizations don’t need to
set up additional operation platform.
◆ The error of structure construction is small and easy to correct.
◆ The climbing speed is fast, the construction course will be quickened.
◆ The formwork can climb itself and cleaning work can be done in the same situs , the used times
of tower crane will be greatly reduced.
- Q:Is the car seat with lumbar support adjustable?
- So it is necessary, some seats with adjustment function, may change the support of the level and the thickness of the protrusion. Later can change the seat or change seats, etc., relatively troublesome.
- Q:JGJ128-2000 door type steel scaffolding specifications only adjustable adjustable screw extension of the base of the relevant provisions of the top of the screw extension of the length of no provisions, but in the specification check the inspection items to check the extension of the screw extension length. What is the standard?
- JGJ128-2000 (JGJ128-2000) Section 9.1.4 of the door type steel pipe scaffolding used as a template support and full of scaffolding, adjustable base adjustment screw extension length should not exceed 200mm. When more than 200mm, the design value of a mast bearing capacity, that is, this specification (5.2.1-5) type Nd should be adjusted according to the adjustable seat extension screw length correction: extension length of 300mm, should be multiplied by the amendment Coefficient 0.90, more than 300mm, should be multiplied by the correction factor 0.80. The height of the template support frame should be adjusted with adjustable jacking.
- Q:Scaffolding brace has several models, respectively, can bear the load?
- They are a lot of good quality models of course, bear the strength of the larger
- Q:Why 2013 BMW 320LI no waist support regulation, and now 2014 models are still not, as a luxury brand is difficult to understand
- Reduce the finished product which can be understood, but as a luxury range of 30-40 million luxury brands, such as Mercedes-Benz, Audi, the whole line, the whole line, Cadillac these are standard, tell the truth that BMW's main movement has been comfortable Compromise the trend, that is, taking into account the movement and comfort, if you take the movement to speak with the simple and undesirable. I really like this section of the paragraph, is not the configuration and give up, the new 3 Series standard wheelbase with the waist support adjustment, but the space can not take into account the comfort of the rear ride.
- Q:BMW 3 Series driver seat waist support how much money
- Outside for more than 300 dollars, not processing, 4S shop almost nothing 1000.
- Q:The permissible range of the top support of the template
- Construction site on the adjustable top care, adjustable base is more common, especially in the template support system inside.
- Q:What does the car support for the waist?
- For the waist is not good or long-distance driving lead to the waist fatigue of the crowd, choose a comfortable waist strap height can ease the long driving caused by the waist fatigue, get more comfort.
- Q:Car plus a tire pressure detection and waist support adjustment about how much money
- Waist support is best airbag, and now have a manual charge and discharge airbags lumbar 50 yuan
- Q:Support on why there is adjustable support and support the set position, that is, where to put any place can not put?
- JGJ 162-2008, Fasteners for fastener steel scaffolding "JGJ130-2011 has been clearly defined in the template support pole must be set U-type top care. As long as it is to support the pole will put, and adjustable section may not be greater than 200mm.
- Q:As the gym did not squat rack, with Smith machine waist twist discomfort, so use the reclining push the practice of squatting, from 40 kg to the current 85 kg. Can this continue to practice it?
- I have seen someone so practice, but with you is the opposite direction, looking at not feel ye, you can talk with the gym, sometimes effective
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Auto-climbing Bracket formwork and scaffolding system
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 m²
- Supply Capability:
- 1000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches