ANSHI 12 Pole FTTH Optical Fiber Termination Box
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 Sets watt
- Supply Capability:
- 100 Sets per Day watt/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The MDU 216 Splitter Terminal from Optic Network Technology is rugged, low cost, low profile interconnection between central office and multi-dwelling units of FTTx application.
The design of MDU 216 splitter terminal combines the functionality of a local convergence cabinet with MDU terminal.
Its multi-layer design allows installers to access only the components necessary for initial installation or subscriber turn-up. It can house the splitter and allows for pigtail splicing of distribution/drop cables as needed.
Features
1. ndoor or outdoor rated
2. available 1x4, 1x8, 1x16 splitter as well as 2x4, 2x8, 2x16 splitter
3. Max. up 16 pcs of FTTH drop cable or pigtails
4. Suitable for wall-mounting or pole mounting application
5. 2 pcs of inlet ports and 16 pcs of outlet ports
Application
1. FTTH, FTTB, FTTC
2. Telecommunication Network
3. CATV
4. Local Area Network
- Q:And then use RJ11 - duckbill jumper to 110 patch panels, is this understanding right? More
- Single frequency cable shielding, you can shield the outside interference. There is no shield of the line, the temporary use can be, and the length can not be too long.
- Q:Six-core cable to each weak there are four, how to calculate the fiber patch panels, couplers, fiber jumpers and the number of calculation methods From the equipment area to the floor wiring room
- The house circuit is not ground line residential circuit generally by the line of fire, zero line, ground, three lines
- Q:How to configure 110 patch panels based on voice points
- ) The design of the wiring harness in the front compartment is especially important, and it is necessary to consider the layout of the engine (horizontal and vertical), the principle of the vehicle and the electrical failure repair in the later period If the wiring harness is designed to Line design, taking full account of the use of each line, diameter, length, etc, then the design of the product is very difficult to economic 2 Product continuity and general In general, the new Austrian electronics in the design of the end of the wire bundle, will try to use the same platform for the mature models as a reference, such as the use of the same electrical function parts, wiring harness accessories (including cable ties, Stent), dressing, etc, from the company's long-term development point of view, which not only reduce the new project new parts of the procurement cycle, and reduce the cost of mold, thereby reducing costs 3 Harness design 3D of today's era, is the era of digital information, what are the pursuit of 3D, of course, the wiring harness design is not out New Austrian electronics in the automotive wiring harness design process, from the source control, the introduction of the concept of electronic loading The so-called electronic loading, that is, in the digital model completely reflect the real state, car electrical function parts, fasteners, rubber parts, etc should be reflected in the number of models In this way, in the design phase to avoid the wiring harness and sheet metal interference problems, to solve the problem of reasonable branches to effectively control the length of the line, so to avoid a lot of late rework phenomenon, but also virtually save the cost
- Q:What is the relationship between the switch and the patch panel?
- This is the CommScope brand of 100 pairs of 110 patch panel models
- Q:Does the fiber patch panel have a pigtail? What are the pigtails in the fiber patch panels?
- There is no, is a chassis and inside the welding plate, as well as inside the accessories. But no pigtail with the flange on the device can not be used. There are FC, SC, ST of these four. Pigtail also sub-carrier level, network level, radio and television level, the best point is the radio and television level, the second is the carrier level, and then the network level.
- Q:There is a line measuring instrument, how to find the seat in the room corresponding to the location of patch panels
- I also encountered similar problems at both ends after adding a corresponding label it
- Q:What is the DDF rack? what's the effect?
- Hello: "Wires" and "cable" in the concept and there is no strict distinction between the boundaries, although the narrow sense of "wire" and "cable", said broadly should be collectively referred to as "cable" The Generally known as a single called "line", more than called "cable"; small diameter called "line", the structure of complex multi-called "cable"
- Q:Integrated wiring inside why the patch panel, directly from the end to the weak place to do the top of the switch to the top of the switch not?
- Yes, the network cable is eight heart. Only two casually on the line. Both ends of the same color on the line. A cable if the ordinary phone can be connected to four, digital phone can only take two. Because the digital phone needs four.
- Q:Will the weak machine room use a hanging cabinet? (Own) to have a heat impact, if you want to use patch panels, put what position more appropriate! The The Ask the great god to help What is the size of the network wiring box? 1
- Generally, if you can not use the floor-type cabinets, you can use the way the wall cabinet, but the engine room is not recommended to use (mainly large line, bearing the big)! You have to do their own words, the main consideration need to consider are: load, load, heat, wiring the four main factors, if you can solve the four main problems, then hanging cabinet can! Weak machine room inside the cabinet may need to install the server and related exchange processing and other equipment, if only a simple weak cabinet, you can consider the use of hanging cabinet problems, pay attention to wiring and out of line and heat on the line.
- Q:How is the line of the patch panel in the LAN? How to get the wiring line on the wiring box.
- Commonly used electrical calculation formulas The first chapter according to the power of the formula one of the formulas 1 Uses: This is based on the power of electrical equipment (kilowatts or kVA) to calculate the current (security) formulas
1. Manufacturer Overview |
|
---|---|
Location | Zhejiang, China |
Year Established | 2001 |
Annual Output Value | US$5 Million - US$10 Million |
Main Markets | North America South America Eastern Europe Southeast Asia Africa Oceania Mid East Eastern Asia Western Europe |
Company Certifications | ISO 9001-2000;SGS;UL;TUV |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Shanghai,Ningbo |
Export Percentage | 31% - 40% |
No.of Employees in Trade Department | 1-2 People |
Language Spoken: | English, Chinese |
b)Factory Information | |
Factory Size: | Below 1,000 square meters |
No. of Production Lines | 10 |
Contract Manufacturing | OEM Service Offered Design Service Offered Buyer Label Offered |
Product Price Range | High and/or Average |
Send your message to us
ANSHI 12 Pole FTTH Optical Fiber Termination Box
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 Sets watt
- Supply Capability:
- 100 Sets per Day watt/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches