Polycarbonate Solid sheetTwin Wall PC Hollow Sheet
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 m²
- Supply Capability:
- 10000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Size of products
Thickness(mm) | 8mm to 30mm |
Length(mm) | No limited |
Width(mm) | Within 2100mm |
Color | Clear Opal Green Blue Bronze lake Blue and so on |
Production line | Two line for PC hollow sheet and One line for PC solid sheet |
Raw materials | The raw materials of pc come from German named Bayer |
Polycarbonate Sheet Sunshine Board
Product Specification
Appearance: board face feel is smooth, level off, no distortion, no bubbles,
Weight, size: in accordance with customer requirements
Colors: clear, lake blue, green, blue, opal, brown, silvery gray, red Conventional etc.
The tensile yield strength:≥60MPa
The bending strength: ≥80MPa
Shaw hardness: ≥80D:
The thermal deformation temperature:(1.80MPa)≥125
Thermal expansion coefficient:(-30℃—+30℃),℃-1≤6.5*10-5
Transmission (8 mm):≥75%
Transmission (solid sheet 3 mm):≥80%
Polycarbonate two wall hollow sheet
Thickness: 4mm / 6mm / 8mm / 10mm
Width: 2100mm
- Q:PC Nai Liban and Sunshine board Which domestic manufacturers of the best products?
- As long as the domestic well-known manufacturers are doing well Such as Huili (sunshine board), solid Lyle, Shanghai Commodities, high Feng, Zheng Cheng, Pu Te, basically all can Because the process is very mature, and now are basically more than the service
- Q:How much of the installation of the sun board installation of a square meter
- This assembly system is mainly used for small facilities such as garage, station canopy, rain eaves, greenhouses and many other alternative glass occasions. When using the wet assembly method, as shown in Figure 2, the basic requirement is that the sealing system is able to withstand a certain amount of movement of the plate, allowing thermal expansion without reducing its adhesion to the frame and the plate. It is generally recommended to use a neutral silicone adhesive and a wet sunboard assembly, but it is important to note that the chemical properties of the sealant used must be checked before use, and acid and alkaline silicone adhesives must not be used because these curing agents Plate cracking, especially when there is internal stress, the choice of sealant, in addition to considering chemical adaptability, but also focus on testing, elongation and weather resistance.
- Q:What can I do with my own sunshine board?
- Own balcony sun block rain, balcony sun room, interior partitions can be ah
- Q:Can the sun board cover the bedroom?
- Sun panels can cover the bedroom, the sun board mainly by the PC / PET / PMMA / PP material production. English is sunlight, referred to as hollow board, pc sun panels to polycarbonate as the main raw material manufacturing. Sunshine board in the mid-80s into the building materials quickly.
- Q:What are the differences between plastic endurance boards and sun panels?
- Category: PC board is generally single and double board, in addition to multi-layer board, wave plate, film.
- Q:What is the difference between sun panels and plexiglass?
- Plexiglass is PMMA polymethyl methacrylate material, commonly known as acrylic. Transmittance of 92%. ??? Not spontaneous combustion but is flammable, do not have self-extinguishing. ??? The average hardness of the Rockwell hardness of about 8,9 degrees. ??? Heat resistance is not high, continuous use temperature exceeds 90 ℃ will heat deformation. ??? Cold resistance is also poor, brittle temperature of about 9.2 ℃.
- Q:What is the difference between a hollow board and a sunboard?
- The material selected for the panel should be FRP, and the selection material for the sun board is PC. The lighting board is fixed with aluminum fastener, and the corrugated board is fixed with a light plate and a self-tapping screw. The position of the lighting plate is generally set in the middle.
- Q:Lighting board and sunshine board which is good?
- This can not say which is better, can only say which product is suitable for you to use, the general enterprise plant lighting with lighting panels, and some flower room on the temperature requirements of the more stringent must use sun panels and shade net supporting the use.
- Q:Can the sun board bend?
- Can be cold bending, but the minimum radius of cold bending does not exceed the thickness of the sunboard 175 times, as said 90 degrees like the bend is certainly not possible. Stamina can, but can not be cold fold, need to be thermoformed.
- Q:Can the stencils be made in the bathroom?
- PC particle board characteristics 1, the surface of the plate can reflect the direct light on the plate of direct exposure, after this treatment can reduce the sunlight penetration. 2, the surface of the board can increase the surface area, while increasing the heat, can extend the service life of the plate. 3, the surface of the plate per square meter distribution of 15,000-18000 pieces of anti-diamond-type particles, reflection, refraction effect can enhance the blocking capacity.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Polycarbonate Solid sheetTwin Wall PC Hollow Sheet
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 m²
- Supply Capability:
- 10000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords