Clear Duct Hose

Hot Products

HDPE Winding Structure Wall Pipe Polyethylene Plastic Pipe

Double Wall Corrugated PE Pipe Plastic Pipe for Water Supply

Buried PE Polyethylene Pipe for Gas Pipeline System

Plastic Pipe in Industrial Field Environmentally Friendly from China

PE Pipe for Water/gas Supply Hot Sale Flexible Hdpe Water Pipe

Coated Composite Steel Pipe for Water Supply System

3 PE Outer Three Layer Polyethylene Anticorrosive Steel Pipe for Gas Oil Pipeline System

Steel Mesh Skeleton Plastic Polyethylene PE Composite Pipe for Gas Pipeline System

DN225mm HDPE Pipes for Water Supply on Sale

Underground Plastic PE Pipes in Coal Mining PE80 PE100

FAQ

Yes, plastic tubes can be FDA-approved for food contact. The FDA sets regulations and guidelines to ensure that food contact materials, including plastic tubes, meet certain safety standards and do not pose a risk to human health.

How can the three plastic pipes be fixed in the installation quota?

PVC pipe sleeve: rigid flame retardant pipe. Rigid PVC pipes and semi rigid flame retardant pipes are rarely used. One is for a roll, and for long distances.

I was changing my engine oil via the dipstick tube and a special suction device that pumps the old oil out of the sump to be replaced with fresh oil. Unfortunately, i had to patch up a hole in the tube on the suction device with parcel tape/sellotape wrapped around and a small piece of tape (around 2x2 square) fell into the engine dipstick tube and appears to have slid down into the oil sump.Will the oil filter make any difference in keeping melted plastic out of the engine? Am i best calling up the manufacturer, not the dealer as i don't want them to know about my error. The engine still runs and i have driven 20 miles so far with no problems. 2009 year Citroen C1Thanks

This is worrisome. As the others say, the worst scenario is the tape gets against the pickup screen and suddenly causes loss of oil pressure. If that happens you will immediately get a low oil pressure warning light but that's something you don't want to happen anyway. However since the piece of tape is 2 x 2 or thereabouts at this point it is almost certainly still rolled up and stuck at the bottom of the dipstick tube. There would not be room for it to easily escape and fall into the sump… yet. There should be one or two screws at the bottom of the dipstick tube to secure it to the engine. If you remove those screws and pull the dipstick tube out, with the dipstick unit, you should find the tape at or near the bottom of the tube. Remove the tape, throw it away, put the tube back in, and sin no more.

Plastic tubes can be used for soundproofing to some extent, but they are not the most effective option. While they can reduce sound transmission, their ability to dampen and absorb sound is limited compared to other soundproofing materials such as acoustic foam or mass-loaded vinyl.

Yes, plastic tubes can be customized in terms of color and size. Manufacturers have the ability to produce plastic tubes in a wide range of colors and can also adjust the size and dimensions of the tubes to meet specific requirements or preferences.

When the fire line is weak, the pipe or plastic pipe is used

Fire tube weak 3 hours fire resistance requirements, galvanized iron pipe and brush fire retardant coating can reach the acceptance criteria of the fire department, so please do not use PVC with the plastic pipe and tube, galvanized tube outside to brush fire retardant coating in order to achieve the 3 hour requirement.

Im making moonshine but not for drinking for fuel. I know that its a bad idea to distill with plastic if your gonna drink it but will it be ok for fuel?

if the plastic can withstand fairly constant temperatures around 180 degrees, then yes. the drawback is plasitc is not a very good heat conductor, and the tubing used in distlling is usually used to allow the hot alcohol to condense back into liquid. metal does this really well, and plastic is an insulator, so it will likely take MUCH more plastic tubing to cool the vapors.

my hamster is stuck in his tube i dont know how to get him out!

Get a used kitchen towel inner-tube, wrap a dish towel round the end for cushioning and use it to very gently ease him out by applying very gentle pressure on his bottom. If the kitchen roll tube is too big, cut down the length of it to make it narrower. Then get rid of hamster tube or cut back on his diet ADDED: Please do not use oil or butter esp as your hamster will then digest this when he is grooming later and it could prove harmful.