Small Home Portable Ice Maker Outdoor Party Camping Ice Maker

Add to Cart

Place Order

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Portable Compact Ice Maker: Ideal for Parties, RVs, Camping Vacations and Boat Tours

Product size: 242×358×328mm

Outer box size: 378×360×373mm

N.W / G.W: 17.2 LBS (8kg) / 20.3 LBS (9kg)

Ice Capacity: 26lb (12kg) / 24h

Water tank capacity: 2.2L

Ice basket capacity: 0.7kg

Rated current: 1.7A

Refrigerant: R600a 0.81oz/23g

2 different ice sizes: small, large

Make ice cubes in 6-13 minutes

Ice shape: bullet ice

Number of ice cubes per cycle: 9

Q:What is the reason that the ice making mechanism is too slow? My friend's ice maker is faster than my ice maker in the same store! Who can help solve the problem?: Lack of refrigerant;The waterway was slightly blocked.I hope I can help you!!

Q:Ice machine has short time to remove ice: 2. Check the position of water level and water level probe3. The water temperature of ice maker shall not be higher than 32 degrees C

Q:Ice maker normal service life: Snowflake Ice Machine Series (40 kg - 350 kg)Freshwater ice machine series (0.3 tons - 60 tons)Sea water ice machine series (1 tons - 6 tons)Tube ice machine series (1 tons - 30 tons)Large edible particle ice machine (3 tons, 5 tons)

Q:Is the ice making mechanism not affected by the environmental temperature?: Condenser motor overloadCheck the running current of the condenser motor, the current setting value of the heat protector and the reset key. Check whether the water pump and the reducer are connected to the groundPLC P05 point, no signal inputPump overloadCheck the running current of the pump motor, the current setting value of the heat protector and the reset button. Check whether the water pump and the reducer are connected to the groundPLC P06 point, no signal inputCompressor high voltage faultCheck condenser fan and condenserPLC P07 point, no signal inputCompressor low voltage faultCheck whether the water inside the ice bucket is normal, ice fall is normalCheck that the system has leaksPLC P08 point, no signal inputFailure of water supply systemCheck whether the water supply system is working properly, whether the water in the water tank is adequate, check whether the water level switch is good, or replace

Q:Ice making mechanism prevents ice from falling properly: Fault reason: measuring water temperature probe fault, making intelligent control system can not effectively perceive water temperature and work, misjudgment, program error, or controller failure.

Q:Do you have the smallest size of a domestic ice maker?: Why don't you just do it in the fridge? Do you need a lot of ice?

Q:Ice machine running 5 minutes to stop what is the matter?: Reason three: high voltage switch openSolution: use the power meter to measure and see if the high voltage switch is normally closed under the stop. If yes, then change the high voltage switch, and also make the two of the switch on the computer board short

Q:TH-110 ice maker adjusts the thickness of ice cubes. "And why does the ice making mechanism stop flowing after a piece of ice?" "it's difficult to push ice out when you have a good piece of ice.": In use, there will be refrigeration ice, but not out of ice, this is because: measuring water temperature probe failure, so that intelligent control system can not effectively perceive the water temperature and work, miscarriage of justice, procedures, errors, or controller failure. The multimeter is used to measure the temperature of the resistance probe (the water temperature in the water tank near 0 degrees C, remove the control box of the three core lines, two lines on both sides of the resistance test), such as resistance in more than 27K, it was judged as controller bad, should be replaced, such as resistance of less than 27K, it shall be disconnect any two lines in a way, through the series resistance of the resistance to 27K to 28K. In use, sometimes ice machine, the machine into the ice removal program (water pump stops working, compressor stop cooling), but ice does not fall off; that is two way solenoid valve damage. Replace the solenoid valve or external loop.

Q:How to use the refrigerator automatic ice maker?: Aftermarket installation. Make sure the pipe is connected and the water supply is normal.2. press the "ice mode" button and choose an ice making model, ice or ice.

Q:Do you have ice making to produce spherical ice? As for table tennis almost?: The ice making system produces spherical ice, similar to the size of table tennis and used in high-end bars.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range