BQ.TADANO MOBILE CRANE GT350E BY TADANO TECHNOLOGY
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 10 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
MASS
Gross Vehicle Mass: 34400 kg
Front axle mass: 12205 kg
Rear axle mass: 22195 kg
PERFORMANCE
Max. traveling speed: 74km/h
Gradeability(tanθ): 46%
Min. Turning radius: 11000 mm
Minimum Ground Clearance: 320mm
1.UPERSTRUCTURESPECIFICATIONS
BOOM
4-section full power partially synchronized telescoping boom of hexagonal box construction with 5 sheaves at boom head. The synchronization system consists of 2 telescope cylinders, extension cables and retraction cables. Hydraulic cylinders fitted with holding valves.
Fully retracted length -----10.6 m
Fully extended length ------ 34 m
Extension speed ----- 23.4 m in 127s
JIB
2-staged boom extension type. Triple offset(5º/25º/45º)type. Stored under base boom section. Single sheave at jib head.
Length --- 8.8 m, 15.2m
SINGLE TOP
Mounted to main boom head for single line work.
ELEVATION
By a double-acting hydraulic cylinder, fitted with holding valve.
Automatic Speed Reduction and Soft Stop function.
Elevation speed -----2º-80ºin /62s
HOIST--Main winch
Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic, brake (Neutral brake) and counterbalance valve. Controlled independently of auxiliary winch.
Single line pull -----31.2kN(3,190 kg)
Single .line speed ----118m/min (at the 4th layer)
Diameter-----16mm '
Length-----.190m
HOIST-Auxiliary winch
Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic brake and counterbalance valve. Controlled independently of main winch.
Single line pull -----34.3 kN ( 3,500kg )
Single line speed -----102 m/min (at the 2nd layer)
Diameter. -----16 mm
Length-----110 m
SWING
Hydraulic axial piston motor driven through planetary speed reducer. Continuous 360~ full circle swing on ball bearing slew ring. Automatic Speed reduction and soft stop function. Equipped with manually locked/released swing brake.
Swing speed -----2.5r /min
HYDRAULIC SYSTEM
Pumps-----Quadruple gear pumps driven by carrier engine through P.T.O.
Control valves-----Multiple valves actuated by pilot pressure with integral pressure relief valves.
Circuit------Equipped with air cooled type oil cooler. Oil pressure appears on AML display for main circuit.
Oil tank capacity-----approx. 527liters
Filters ------Return line filter
CAB AND CONTROLS
By 4 control levers for swing, boom hoist, main winch, boom telescoping or auxiliary winch with 2 control pedals for boom hoist, boom telescoping based on ISO standard layout. Control lever stands can change neutral positions and tilt for easy access to cab.
Steel construction with sliding door access and tinted safety glass windows opening at side, and operator's 5 way adjustable seat with headrest and armrest.
OUTRIGGER
4-hydraulically operated H-type outriggers. Each outrigger controlled simultaneously or independently from either side of carrier. Equipped with sight level gauge. Floats mounted integrally with the jacks retract to within vehicle width. All cylinders fitted with pilot check valves.
Crane operation with different extended length of each outrigger.
Equipped with extension width detector for each outrigger.
Extended width
Fully-----6,100 mm
Middle-----4, 000mm
Float size (Diameter) -----400 mm
TADANO Automatic Moment Limiter
Main unit in crane cab gives audible and visual warning of approach to overload. Automatically cuts out crane motions before overload. With working range (load radius and / or boom angle and / or tip height and / or swing range) limit function.
Nine functions are constantly displayed.
Either moment as percentage or main hydraulic pressure
Either boom angle or moment %
Either boom length or potential hook height
Either actual load radius or swing angle
Actual hook load
Permissible load
Either jib offset angle or number of parts of line of robe
Boom position indicator
Outrigger position indicator
FRONT JACK
Front outrigger mounted to the front frame of carrier to permit 360ºlifting capabilities.
Hydraulic cylinder fitted with pilot check valve. Equipped with front jack extension detector.
Float size (Diameter) -----260 mm
COUNTERWEIGHT
Integral with swing frame
Mass-----4100 kg
DEMENSION
Overall length-----12,770mm
Overall width-----2,490mm
Overall height-----3,570mm
- Q:What is the relationship between all-terrain cranes and tire cranes?
- All-terrain truck cranes are truck cranes that are specially developed for cranes. Although they are still truck cranes, their chassis are only dedicated to cranes and can not be used for other purposes. However, they are usually larger tonnage, ranging from tens of tons to hundreds of tons
- Q:What are the types of truck cranes?
- According to the type of leg: frog-style legs, x-type legs, h-type legs.
- Q:What is the difference between a crane and a crane?
- The function of the crane and the crane is the same, the crane is included in the crane, but the crane has a greater category.
- Q:What are the four kinds of truck cranes?
- The four cylinders of a truck crane generally refer to the telescopic cylinder of the boom (adjusting the length of the boom)
- Q:What is the brake lock of a truck crane?
- Small gap slowly leak, can not be on the various agencies or hydraulic motor hydraulic cylinder to achieve effective locking, which prone to heavy lifting down, the boom shrinkage, increased range, the sinking of the accident, ranging from the car crane can not
- Q:What is the principle of car hanging arm?
- The two ends of the cylinder and the cylinder are respectively hinged to the bottom end of the first telescopic arm and the top end of the third telescopic arm
- Q:What is the difference between a truck crane and an all-terrain crane?
- If the four wheels to the ground, like the car holding the crane, is the car crane.
- Q:What are the main parts of the truck crane?
- Truck crane is a crane installed in the car chassis on a lifting transport equipment, due to a flexible, able to walk faster operating characteristics
- Q:What is the development trend of truck cranes in China?
- China's automobile crane production enterprises in order to survive and develop in the field, need to do a lot of things
- Q:What is the material process for a truck crane?
- And the price, crane parts such as Wanda rotary bearing manufacturing also benefited from the continuous emergence of new materials, making the crane to a lighter, better direction.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
BQ.TADANO MOBILE CRANE GT350E BY TADANO TECHNOLOGY
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 10 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords