aluminium wire AA5052 0.05MM-0.95MM for mesh

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Descriptions Of Product Aluminum Wire

Product		Pure aluminum	Corrosionresisting aluminum alloy
Brand		YH-301	YH-331	YH-5356	YH-311
Standard and steel grade	GB	S301	S331	S5356	S311
Standard and steel grade	AWS	ER1100	ER5183	ER5356	ER4043
Gauge Φ(mm)		0.8-5.0	0.8-5.0	0.8-5.0	0.8-5.0
Welding wire chemical composition(%)	Cu	0.05~0.20	≤0.10	≤0.10	≤0.30
	Si	≤1.0	≤0.40	≤0.25	4.5~6.0
	Fe	-	≤0.40	≤0.40	≤0.80
	Mn	≤0.05	0.05~1.00	0.05~0.20	≤0.05
	Mg	-	4.3~5.2	4.5~5.5	≤0.05
	Cr	-	0.05~0.25	0.05~0.20	-
	Zn	≤0.10	≤0.25	≤0.10	≤0.10
	Ti	-	≤0.15	0.06-0.20	≤0.20
	Al	≥99.5	Rem	Rem	Rem
Application	YH-301	Good plasticity,primarily used for gas welding and argon-arc welding of corrosion-resisting pure aluminum
	YH-331	High strength,good corrosion resistance,primarily used for argon-arc welding of aluminum alloy
	YH-5356	Outstanding corrosion resistance,high strength,exceptional versatility,,primarily used for argon-arc welding of aluminum alloy,especialy for 5083 aluminum alloy
	YH-311	Outstanding corrosion resistance,exceptional versatility,primarily used for welding and MIG welding of aluminum alloy,especially good for 4043 aluminum alloy ,Not recommended to use for welding of magnesium alloy.

Q:Why do copper ions insert aluminum wire and red material will appear on the surface of aluminum wire?: The function activity of metal is the standard electrode potential of metal (up to E) and the standard Gibbs free energy reaction with water (G, up to) and their transformation formula between the:Turn left and turn right |Therefore, the more negative the electrode potential, the greater the free energy and the stronger the activity. A factor free energy is the enthalpy change (delta H). When the metal elements form cations in water, they undergo sublimation, ionization, hydration, and the three steps have energy changes in the three steps, which determine the total enthalpy change, and have a great impact on the activity of metals. Therefore, the sublimation energy, ionization energy and hydration heat of metals should be taken into account in the analysis of the causes of metal activity.

Q:What do you want to do with the BJD?: There are three solutions:1, add aluminum wire (the most troublesome)2, plus gaskets (easier to remove only part of the joint of the arm or leg, do not have to disassemble the trunk)3, re tension, adjust the tightnessNovice can take the child to the store, pay to allow the store to help, if you can see the whole process, and the second time they will pull the tendons / pads

Q:LV how to solder, seek expert advice, please everybody: Set the tightness of the wire brakeTightness only need to ensure that the wire will not loose, but not too tight, otherwise it will cause the welding wire to drag and drop. To correct the setting, first the tightness to the minimum, and then put on the welding wire, let it through the drive roller, if in addition to welding wire roller is moving, and other parts have stopped, that is not tight enough. Be careful when handling, because too tight will cause excessive force on the wire. In addition, do not strain the last few laps of the wire when it is out of use; it is usually difficult to loosen because the wire is too hard.

Q:How do the radiator from the Water Leakage: If the first is trachoma, heating switch off, let the water inside, then use soap to plug the blisters Water Leakage, and then use plastic glue (glue, a bit like plasticine) to Water Leakage, after the glue dry. I use this method, so that it is convenient and effective.

Q:Home wire, can not use aluminum thread?,: No problem. 4mm2 is enough. The home line used to be 2.5mm2.

Q:The bottom of the cooker is leaking. How can it be repaired?: The bottom pad a piece of iron or hard objects, and then gently hammer with a small hammer, and then turn over, both sides beat each other, until completely riveted, it is best to use sandpaper can be polished.

Q:Is the wire on the diode a type of P and N semiconductor? Or P semiconductor?: One end of the fine aluminum wire is connected to the anode lead, and the other end is pressed on the doped n type semiconductor. After adding the voltage, the fine aluminum wire melts at the contact point and penetrates into the melted part. In this way, the contact point is actually a p type semiconductor and attaches to the N type semiconductor to form a PN junction.

Q:Is it OK to use 6 square aluminum wire for transformer high voltage wire?: 6 square aluminum wire is very small, it is easy to break

Q:What's the color of the copper core section of the cable?: Of course, the quality of pure copper is the best, non - pure copper can not be said to be false, as long as the line with the five lines of standards can be.

Q:Is the polyurethane plastic made of transparent wrapped aluminum silk easy to yellow?: If you want permanent resistance to yellowing, you can only use the aliphatic, but the price of this raw material is high.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range