Track Lights For Kitchen Ceiling

Hot Products

Good quality plastic indoor pvc panel for wall and ceiling for petrol station

Kenya pvc ceiling panel pvc ceiling designs pictures

Pvc ceiling sheet pvc ceiling panel from CNBM

Printed PVC Ceiling Wooden Design PVC Ceiling

Rigid PVC Board Celuka Foam Board PVC Foam Sheet

waterproof interlock pvc wall panel interior wall coating panel

PVC Ceiling Tiles-Interior Decoration System

PVC Ceiling for Bathroom White PVC Ceiling

PVC Panel for Interior Decoration System-Laminated Series

PVC Panel for Interior Decoration System-Foiled Series

FAQ

Blister and PVC board distinction. Detailed description of the best.

Blister board is an amorphous, odorless, non-toxic, highly transparent colorless or slightly yellow thermoplastic engineering plastics, with excellent physical and mechanical properties, especially excellent impact resistance, tensile strength, bending strength, compressive strength High stability, low stability, good heat resistance and low temperature resistance, in a wide temperature range with a stable mechanical properties, dimensional stability, electrical properties and flame retardant, can be in -60 ~ Long-term use at 120 ℃; no significant melting point, melting at 220-230 ℃ state; due to the large molecular chain, resin melt viscosity; small water absorption, small shrinkage, high dimensional accuracy, good dimensional stability, Oil resistance, but not resistant to ultraviolet light, good weather resistance; oil, acid, intolerant alkali, oxidizing acid and amine, ketones, soluble in chlorinated hydrocarbons and aromatic Solvent, long-term in water easily lead to hydrolysis and cracking, the disadvantage is due to poor fatigue strength, prone to stress cracking, solvent resistance is poor, poor wear resistance. PVC board is PVC as raw material made of cross-section for the honeycomb mesh structure of the plate, is a vacuum plastic film. For all types of panel surface packaging, it is also known as decorative film, with film, used in building materials, packaging, medicine and many other industries. Which accounted for the largest proportion of building materials industry, 60%, followed by the packaging industry, there are several other small-scale application of the industry. According to the degree of soft and hard can be divided into soft PVC and hard PVC, according to the production process can be divided into PVC leather foam and PVC free foam board. General performance PVC resin is a white or light yellow powder, the relative density of 1.35-1.45. The softness of the product can be achieved by adding

What is the best glue on the PVC board glue?

Pvc special glue, hard and soft different

Home decoration with PVC buckle hanging crane top, want to buy crystal lamp, but do not know whether the pvc Kouban can withstand the weight of crystal lamp!

I am learning to build, pvc is polyvinyl chloride

Want to use the PVC board to do the model, you can color it? Gouache paint, paint can you?

Can be colored, the material itself does not resist the pigment

VC plastic buckle the corners of the corners is how fixed to the wall of the buckle is how and cords connected to the light steel keel and gypsum do cut off the light steel keel is how and the wall ...

Light steel keel sub-station dragon and Wolong. Wolong before the installation of the first hammer with a hammer, playing wooden needle, and Wolong fixed, and then install the station dragon, and clamp with a good fit.

PVC ceiling plate how to disassemble

First of all, you have to observe the buckle board, the general edge of the last piece is not a block, then this piece is not the whole piece is the last piece, but also to first remove a piece, Hold down the last piece of the hand to the wall hard push, to 2 side to push, light push side is not enough, you push this piece in the end, you will find and another side of the office has been divorced, and then You can directly win, and the second plate will remove the screws, the screws in the middle of the wood, directly screw down on it, the screw down and then pull down this board also down, and then Repeatedly, the top is removed!

Wood board and PVC board with what glue combination

Universal glue full coating, thin coating, pressure paste. Or glass paste point paste.

Members XDJM: I work for reasons, a set of home hair blank room idle, recently wanted to simply rent out the rent. A friend said that the floor can be used home PVC floor shop, but we do not understand these things, please help my friends to answer my question, thank you: 1, the thickness of the general requirements of home PVC floor is how much? Requirements can not be easily trampled, hit rotten. 2, PVC floor of the construction conditions is what? Molding room floor can be used directly? 3, my home or the developer of the floor when the developer, the cement is not particularly flat (there are more holes, as if there is no cement road level), with what 4, some people say to brush plastic, need not? Hope that these or their own use of the reply, I only 30 points, all the reward

You said the ground is not cement road level, there are a lot of holes, I do not know you are not the ground is the sand from the like, if there is a sand from the proposed you do not do cement self-leveling so that the quality of your floor There is no guarantee that the ground is not cement road Ping suggested that you do not do cement self-leveling and do not say how the effect of the cost is too high, the cement self-leveling to find someone to do the price of 15-25 yuan per square meter, and cement self-leveling Each can only do 2-4MM meters, that is to say that you want to make a good effect at least have to do 2 to 3 times, so the cost is too high, I do many years of PVC flooring, it is recommended that you shop The ground before the first to find a good way to find the mud on the ground so that you will be less to a lot of cost and the effect of the bottom out of the floor will be much better