Butterfly Valve Price Sanitary Stainless Steel with Good Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images：
4.Manual Wafer Butterfly Valve Specification：
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q:How does the valve open?
- Now the valve is in a closed state, the general valve on the valve flow direction marked, like you figure on this, flat side perpendicular to the flow channel is closed, parallel to the flow channel is open.
- Q:What are the uses and differences of gate valves, butterfly valves, ball valves and other valves?
- The use of the same difference, you can see the shape
- Q:What does the valve stroke mean?
- The distance from one position to another. Usually in the first position of the cut position, the second position is put through the position. Unless the valve has 3 positions.[1] to determine the stroke of the valve is the valve and valve two, closing stroke of its opening height, the valve opening height to diameter of the valve is fully open, 1/3, so the opening height is part size below the path + gate is closed.[2] valve: valve (Famen) is a fluid conveying system control components, with a cut-off, regulation, diversion, to prevent reverse flow, voltage regulation, shunt or overflow, pressure relief and other functions. Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
- Q:According to the original valve installed on it, but never demolished, I am afraid to force over, will not be broken? The old valve, that part of the remaining three tubes tight.
- 1. Prepare the glue and saw blade. Disengaging bracket.2, using a hand saw from the valve mouth (spool near) transverse incision.3, the center will be on the move, the longitudinal incision, be careful not to damage the inner tube.4. Clean the pipe mouth, pipe and new valve coating, install the valve.Turn left and turn right |
- Q:Look at the flow chart, some of the valves are marked with FV, and some are marked with XV. What does that mean?And what do you mean by the Cv value on the valve nameplate?I hope the heroes give a clear explanation ah, it is best to give an introduction of this knowledge of the web site oh.Thank again.
- FV: flow control valveLV: level control valveCV: flow coefficient flow coefficient CvFlow coefficient of an imperial unit. Is equal to the temperature of 40 degrees Fahrenheit Fahrenheit water in -100 1psi (6894.8Pa) 1min flows through the valve pressure drop US gallonThe domestic habits called Kv, Kv said that the valve flow capacity, it is defined as: when the control valve fully open, the valve pressure difference at both ends of a P 100KPa, R 1gf/cm3 (severe fluid that is often warm), per hour through the number of flow control valves, with m3/h or t/h.Cv=1.167Kv
- Q:What valve is the VENT?
- VENT position usually refers to the valve on the leak detection valve, relief valve, but not the same as the use of DRAIN, which is used for sewage.
- Q:How does the valve rust die?
- Go to the hardware store to buy derusting lubricant, W40 is fine.
- Q:1/2, what does 1/4 valve mean? I don't understand. What does this number mean? Have a valve to introduce me, do not copy a pile of online introduction, I want to concise
- I have to answer a simple 1/2 1/4 is American Standard valve diameter to the national standard to calculate it is 1/2=DN15 1/4=DN8Also on the valve size of the meaning of the Wenzhou essence valve factory for you to answer
- Q:I'm going to put a solar energy and an electric water heater installed in the same hot water pipe, a valve, a valve open and close the valve B and vice versa the installation of solar and electric water heater, there can be no linkage valve?
- In industry, you say this, such as using two butterfly linkage and composition of the three-way valve to use. But civilian should be few, demand is very little ah. It is estimated that you can only install two valves and then use both hands at the same time to perform linkage.
- Q:Pump, valve, these belong to the material?
- The pump belongs to the equipment (electromechanical equipment), and the valve belongs to the pipeline material.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Butterfly Valve Price Sanitary Stainless Steel with Good Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords
